study on the fibre reinforced concrete using steel slag as the coarse aggregate replacement submitted to jawaharlal nehru technological university kakinada in partial fullfillment of the requirement for the award of the degree master of technology in structural engineering by mallavarapu rama harshitha (14kq1d8703) under the esteemed guidance ...Experimental Study on Partial Replacement of Fine Aggregate by Steel Slag. International Journal of Innovative Research in Science, Engineering and Technology. (2014), ISSN: 2319-8753, Vol. 3, Issue 11, and Pp- 17402-17408. [2] BIS 10269:53: Specification for …

Prof. Warudkar Abhijit A., Mr. Nigade Y.M "Technical Assessment on Performance of Partial Replacement of Coarse Aggregate by Steel Slag in Concrete", International Journal of Engineering Trends and Technology (IJETT), V30(1),37-41 December 2015. ISSN:2231-5381. published by seventh sense research group. Abstract Road Construction is an activity in which natural …Lightweight aggregate with a nominal size of 14 mm was used as coarse aggregate in mix LWC-2, and coarse steel slag (4.9–20 mm) was used to replace all coarse aggregate in mix CSSC-2. For mix SSGC-2, waste glass (4.9–10 mm) was used to replace 17.5% by volume of coarse aggregate, and the remaining coarse aggregate was replaced by coarse ...

The results of investigation indicate that partial replacement of coarse and fine aggregates by steel slag develops the tensile, compressive and flexural strength of conventional concrete. The investigation also observed that mass loss in cubes is very low after concentration in acids and deflection of RCC beams steadily increases due to ...Steel slag was found to be the best replacement for natural aggregates of concrete. Steel slag which is produced as a waste material in the steel industry and has a negative impact on environment when disposed. In the course of future project work by the replacement of steel slag for the coarse aggregate in concrete of 25%, 50%, 75% & with ...

Scrunity on Partial Replacement of Steel Slag as Coarse Aggregates and Fine Aggregates with Echo Sand International Journal of Applied Sciences, Engineering and Management ISSN 2320 – 3439, Vol. 08, No. 05, September 2019, pp. 44-49 clay together. The burning process changed the chemical properties of the materials and Joseph Asphidn createdconcrete with partial replacement of fine aggregate by copper slag with various percentages of 0%, 10%, 15% and 20%. The specimens were casted for 7days, 14 days and 28 days then tested. The results are presented above. V. REFERENCES [1] Al-Jabri, K. and Makoto Hisada. "Copper slag as sand

Appropriate utilization of the combination of these two materials as a partial replacement for cement and coarse aggregate will bring ecological and economic benefits to the country. II. MATERIAL PROPERTIES Material Used 1) Cement 2) Coarse Aggregate 3) Fine Aggregate 4) Replacement steel slag (partial Replacement of coarse aggregate 40%, 50% ...partial replacement of coarse aggregate with iron slag in the cement concrete: In this study partial replacement of of coarse aggregate with iron slag in the cement concrete have greater strength than the conventional concrete. As the self weight of this concrete is higher. The polypropylene fibres are free from water absorption.

12%In this study, an attempt has been made to investigate the effect of partial replacement of conventional river sand with steel slag aggregate. The replacement of river sand by slag aggregate provides dual advantage of reducing disposal problems in steel industries and conserving the natural resources.concrete by using steel slag and waste limestone aggregate as partial replacement to fine aggregates and coarse aggregates. The compressive strength test is studied for 7 and 28 days of curing period and the split tensile and flexural strength is studied for 28 days of curing period.

This paper aims to study experimentally, the effect of partial replacement of coarse aggregate by steel slag (SS), on the various strength and durability properties of concrete, by using the mix design of M40 grade. In this study, steel slag was used as a coarse aggregate replacement in conventional concrete mix. Steel slag was selected due to its characteristics, which are almost similar …Nandini Suri et al., (2016) "Experimental Investigations On Partial Replacement Of Steel Slag As Coarse Aggregates And Eco Sand As Fine Aggregate", Int. J. Civil Eng. Technol. (IJCIET), Volume 7, Issue 5, September-October 2016, pp 322-328.

partial replacement of coarse aggregate with steel slag keeping fine aggregate replacement consistent and durability study on replaced fine and coarse aggregates 1 g. subbarao, b.tech, pg scholar 2p. nageswararao, m.tech,(phd), assistant professor civil dept, asr colleage of engineering, tanuku, andhra pradesh, india abstractStrength Analysis of Concrete by Using Iron Slag as a Partial Replacement of Normal Aggregate (Coarse) in Concrete Khalid Raza1, Apoorv Singh2, R. D. Patel3 1,2P.G. Scholar, Department of Civil Engineering, M.M.M.U.T. Gorakhpur, India Abstract: Iron slag is an industrial waste by-product of steel industry. The demand for aggregate in ...

The partial replacement of M- sand by steel slag with 10%, 20% and 30% to find the optimum percentage of replacement. Using optimum percentage as constant, the Coarse Aggregate is replaced with certain percentage by E-Waste.Steel slag and blast furnace slag aggregates were used as partial replacement of conventional coarse and fine aggregates respectively. Dense Bituminous Macadam grade-I as per Ministry of Road Transport and Highways (MORTH) specification is selected for the present study. The conventional aggregates were replaced with varying dosages of 10, 20 ...

Abstract This paper aims to study experimentally, the effect of partial replacement of coarse and fine aggregates by steel slag (SS), on the various strength and durability properties of concrete, by using the mix design of M20 grade. The optimum percentage of replacement of fine and coarse aggregate by steel slag is found. Workability of concrete gradually decreases, as the percentage of ...Mineral admixture : Steel Slag Fine aggregate : Natural Sand & M - Sand Coarse aggregate Water Chemical admixture : Super plasticizer Cement-The cement used for casting the specimens is of 53 grade ordinary Portland cement as per as per IS 12269-1987. The required quantity is procured, stored in airtight bags and used for experimental programme.

Portland Cement 53 grade, fine aggregate, coarse aggregate and steel slag for checking their suitabilities for making concrete. Mix proportions of concrete are modified for using EAF steel slag with partial replacement of coarse aggregate replaced with 0%, 25%, 50%, 75% and …This paper aims to study experimentally, the effect of partial replacement of coarse aggregate by steel slag (SS), on the various strength and durability properties of concrete, by using the mix design of M40 grade. In this study, steel slag was used

partial replacement of fine aggregate by steel slag on the various strength properties of concrete by using the mix design of M20 grade. Test specimen with 0, 10, 20, 30, 40&50% of partial replacement of fine aggregate by steel slag were cast and tested for compressive strength after curing period of 7 …Steel slag was selected due to its characteristics which are almost similar to conventional aggregates and the fact that it is easily obtainable as a by-product of the steel industry. Steel slag has been considered for replacement of coarse aggregate in binder layer …